Platform Framework Cabinet Input Power Plugs and Receptacles

Platform Framework Cabinet Input Power Plugs and Receptacles - BAR Managed Servers

Teradata Platform Framework Cabinet Model 12 Product and Site Preparation Guide

Product

BAR Managed Servers

Published

February 2018

Language

English (United States)

Last Update

2018-04-18

dita:mapPath

lur1471887722020.ditamap

dita:ditavalPath

9212.ditaval.ditaval

dita:id

tlu1471650703436

Product Category

Hardware

Platform Framework Cabinet Four-Cord 30A/32A Splash-Proof Power Plugs and Receptacles

The following plug type is for worldwide use. It is used phase-to-phase in locations with traditional North American power and single phase (line-to-neutral) in locations with traditional European power.

Platform Framework Cabinet Four-Cord 30A/32A Splash-Proof Power Plugs and Receptacles
Unit	PFC Cabinet
Power Type	30A/32A phase-phase or single phase power
Nameplate Rating a b	24A per cord 200-240V~
Expected Utility Power Sources (Provided by Site)	230 V wired line-to-neutral (single-phase) . With this line-to-neutral source, the power plug connects to line, neutral, and safety ground. This utility source is typical in Europe, but is now sometimes found in North America in new, specialized data centers. Or Wired line-to-line (phase-phase) This utility source is typically used in North America and Japan. Three-phase Wye with a line to neutral voltage typically 120V or 127V and a line to line voltage of 200V to 240V. Alternate expected power source (Japan): Delta power source 200V to 240V on each side. With either of the previous two utility power sources, each of the 3-pin power plugs connect to two of the three lines and also to safety ground. With these sources the power plug does notconnect to neutral.
Power Plug and Number of Cords (Supplied with Product)	IEC 60309 CEE17, pin and sleeve, 30/32A, Blue (250V), 2P3W, with 6-hour keying, IP44 splash-proof plug (Walther Electric brand is shown below. Actual brand supplied with cabinet may vary.) Four AC box cords per cabinet, top or bottom egress. The minimum bend radius limit for the power cord is 12.8 cm (5.0 in.). Do not bend the power cord tighter than this limit.
AC Box Power Cord Connections to Site Power (For Redundancy)	The two power cords on the orange AC box in the cabinet connect to one site power source. The two power cords on the blue AC box in the cabinet connect to the second site power source.
Power Receptacle or Connector and Circuit Breakers (Provided by Site)	IEC 60309 CEE17, pin and sleeve, 30/32A, Blue (250V), 2P3W, with 6-hour keying, IP44 splash-proof receptacle or connector Example receptacles (similar products are available from other companies): Scame Electrical Solutions SCM330R6S (shown above) Walther Electric 430306 Example connectors for use with cordage (similar products are available from other companies): ABL Sursum K32S20A Scame Electrical Solutions SCM330C6S Walther Electric 330306 (shown above) Walther Electric 331306 Example connectors for use with ¾-inch NPT fitting for connection to conduit: c Walther Electric PG21-75 combined with Walther Electric 331306 Customer to supply four receptacles or connectors per cabinet. d One site circuit breaker required for each power cord; customer must provide required site circuit breakers. Each AC box on separate power source connection.
a Do not use this table to determine power consumption, to estimate current draw, or to estimate heat generation. For these parameters, see Site Environmental Planning. Nameplate ratings are a statement of product certification. b Frequency rating is 50 or 60 Hz for all products. c Conduit Adapters do not connect to the ground terminal of the connector. Consult your local code grounding requirements before using adapters. d Obtain connectors by ordering kit 2021-K900. Two kits are required per Platform Framework Cabinet.